250 Important Engineering Drawing MCQ Question and Answer | PDF Free Download
1.In offset sections, offsets or bends in the cutting plane are all:
- A90 degrees
- B180 degrees
- CEither 90 or 180 degrees
- D30, 60 or 90 degrees
2.This type of solid is formed by sweeping a shape along a linear path:
- APlanar solid
- BRevolved solid
- CWarped solid
- DExtruded solid
3.In perspective drawings this is placed between the observer and the object:
- AVanishing point / horizon
- BStation point
- CGround line
- DPlane of projection / picture plane
4.Once the architect has finalized the house plans with the client any changes to the design requested by the client will require a
- AChange order
- BModification slip
- CWhole new set of drawings
- DNone of the above
5.Auto-CAD refers to isometric ellipses as
- AEllipses
- BIso-ellipses
- CIso-circles
- DCircles
6.A civil engineer working on a bridge design would probably rely on his ________ scale for checking printed drawings.
- AEngineer's
- BMetric
- CArchitect's
- DNone of the above
7.These items typically are not used in new designs, but are still common in high-power amplifiers:
- AAmplifier tubes
- BElectron tubes
- CSignal relays
- DSwitches
8.Which of the following is one of the basic types of welded joints:
- AT-joint
- BRear joint
- CAngle joint
- DGroove joint
9.The daily workload of a ________ drafter would generally include technical drawings of machine parts.
- AArchitectural
- BCivil
- CElectrical
- DMechanical
10.The Auto-CAD command used to combine two or more primitive shapes into a single complex 3-dimensional model is ________.
- AAdd
- BUnion
- CAttach
- DForm
11.This type of surface is tipped to all principal planes of projection and does not appear true size in any standard view:
- AForeshortened
- BParallel
- Cv
- DOblique
12.On a floor plan the dashed line that appears approximately 24" outside the exterior wall represents the ________.
- ASidewalk
- BRoof overhang
- CPlumbing drain lines
- DNone of the above
13.The ________ tool on the Dimension tool bar places the length of an arch on a drawing.
- AArc Radius
- BArc Length
- CRadius
- Dv
14.Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
- AType @3<45 and enter
- BType 3 back slash and enter
- CType 3 forward slash and enter
- DType 3 and try to use the Dynamic Input readout to find the end point
15.An engineer's scale would be used to measure lines on a drawing where the scale factor reads ________.
- A1/4" = 1'-0"
- B1/8" = 1'-0"
- C1" = 100'
- D3/4" = 1'-0"
16.These types of pipes are generally connected with bell and spigot joints or flanged joints:
- ASoil and waste
- BWater and gas
- CWater and steam
- DGas and soil
17.Switches and relays should be shown in this position with no operating force or applied energy:
- ANormal
- BClosed
- COffset
- DApplication
18.When using versions of Auto-CAD prior to Release 2006 it may be necessary to ________ a block in order to edit it.
- ACopy
- BExplode
- COffset
- DNone of the above
19.This type of circuit is a semiconductor wafer or chip:
- AIntegrated circuit
- BTransmission circuit
- CPlotted circuit
- DConducted circuit
20.On typical electronic diagrams, these items need not be shown unless they are needed for clarification:
- ATransmission diagrams
- BOperating relays
- CClosed relays
- DTerminal circles